Teamlink 3104/08/16 EE Ethernet over PDH converteruses the next PDH technology such as generic framing generation procedure(GFP G.8040), Virtual concatenation (VCAT G.7043) and link capacity adjustment scheme(LCAS G.7042).

SNMP-based element management software provides SNMP traps, status polling, and configuration. Remote element management is available in Teamview EMS.

The devices are managed in-band or out of band from the Fast Ethernet user port or via the TDM port. Management traffic and user Ethernet traffic are transported together on the same Ethernet flow, seperated by different VLANs, thus ensuring traffic sercuirty based on port based or tag based VLAN.


       Product Features     


Discription

Teamlink 3104/08/16 EE is intelligent converter connecting Fast Ethernet LANs over E1 circuits. They enable service providers and ISPs to supply Transparent Ethernet servies, without interfering with user traffic.

The 802.1p priority scheme enables user to define four different QoS levels, according to the application requirement.

The Fast Ethernet bridge handles frame size settings to 1522, 1526, 1654, 1784 bytes.

Sends Alarm notification to Manager IP address for the following :

E1 : Up / Down.

Ethernet : Up / Down.

Loopback : On / Off.

If the ethernet error packets or collusion packets are reached more than threshold values.

Features

Connect Fast Ethernet Lans over E1 circuits.

E1 port Enable / Disable Selection.

Inband and out-of-band management access vis:

Local and Remote Loop backs for the diagnostics.

   ASCII terminal

   Telnet.

   SNMP.

   Teamview - EMS.

Wire-speed packetforwarding.

4-levels of QoS, based on four VLAN priority queues as per 802.1p.

Ethernet Frame size settings.

VLAN Tagging Un Tagging.

MAC table Display.

Ethernet transmit,Receive,Collision and error packets display.

Ethernet Rate Controle..

Special tag for the management traffic that will transmit in the same traffic to ensure the inband management functions..

Enables the higher bandwidth capacity Ethernet Services to Remote locations.

TEAMLINK 3104 uses next generation Ethernet Over PDH network protocols like GFP(G.8040), Virtual Concatenation (VCAT G.7043) and Link Capacity adjustment scheme (LCAS G.7042).

Inter operable with the any device which is using the standard Protocols like GFP,VCAS,LCAS for connectiong.

VLAN - aware and VLAN - Unaware operation.

Wire speed packet forwarding based on No.of E1s.

General Specifications

INDICATORS

PWR-Power status

E1 Los - Los of E1 Signal.

Link1 - Fiber Ethernet Port Link

SPD1 - Fiber Ethernet Port Speed

Link2 -Copper Ethernet Port Link

SPD2 - Copper Ethernet Port Speed

Technical Specifications

E1 INTERFACE

Number of ports: 4/8/16

Compliance: G.703/ G.704

Data Rate: 2.048 Mbps

Line code: HDB3, AMI

Line Impedence: 120Ohms, balanced

System clock: Internal or loopback timing

Diagnostics: Remote and local loopback

Connector: RJ-45

ETHERNET INTERFACE

Type: 10/100 Base-TX and 100 Base-FX Mbps auto negotiation, full/half duplex, flow control.

Compliance: Confirms to the relevant sections of IEEE 802.3 and 802.3U

Connector: RJ-45 and LC type for fiber.

WAN Protocol

TEAMLINK 3104/08/16 EE uses next generation Ethernet Over PDH Virtual network protocols like GFP(G.8040), Concatenation(VCAT G.7043) and Link Capacity adjustment scheme(LCAS G.7042)

Type: GFP(VCAT & LCAS)

CRC Type: 16 or 32 bit selection.

Power

AC: 100 to 240 VAC (+10%), 50 to 60Hz

DC: -48 VDC (+10%).

Power consumption: <2W

Environment

Temperature: 0 - 50 C/32 - 122 F

Humidity: Up to 95% non-condensing.

Ordering:

Teamlink 3104/08/16 EE Managed Fast Ethernet over 4 E1 converter.

Teamlink 3104/08/16 EE Managed Fast Ethernet over 8 E1 converter.

Teamlink 3104/08/16 EE Managed Fast Ethernet over 16 E1 converter.

  SUPPLIED ACCESSORIES:

    AC/DC power cord or adapter plug.

    nterface adapter for converting a balanced E1 RJ-45 connector to a pair of BNC unbalanced coaxial connectors supplied when ordering E1 unbalanced option.

    FX port is Ordering time Optional.

FE Over 4/8/16 E1 CONVERTER Applicaton Diagramme


Channel Capacity : 4E1

Bit Rate : 2.048Mbps + / - 50ppm .

Line Type : Balanced 120 Ohms

Bit Rate : 155Mbps

Wavelength : 1310nm/1550nm [Optional]

Optical Connector : LC / SC / FC / PC [Optional]

No. of Interfaces : 4 [ Optional]

Interface : 10 Mbps or 100 Mbps auto sensing

Connecter : RJ -45