TEAMLINK3004 SHDSL modem is a 2 or 4 Wire operative modem Works from 64Kbps to 2048Kbps insteps of 64Kbps speeds Long reach up to 11Kms for standard 64Kbps speed
TEAMLINK3004 SHDSL modem is a 2 or 4 Wire operative modem Works from 64Kbps to 2048Kbps insteps of 64Kbps speeds Long reach up to 11Kms for standard 64Kbps speed
Configuration Through DIP Switches
Provides multi stage line protection as per K.20 and K.21.
External Secondary optional Line Protection Device
Long reach up to 11Kms. for standard 64Kbps speed
LED Indications for easy Monitoring
Front Panel Switches for Diagnostics or Loopbacks
Supports 230V AC and 48V DC with the Same Socket
Works from 64Kbps to 2048Kbps insteps of 64Kbps speeds
Line type : 2 or 4Wire twisted copper wire of 0.5mm Diameter.
Line Code : TCPAM as per the ITU-T G991.2 ( Annex –A and Annex –B ).
Bandwidth : Operates From 64Kbps to 2048Kbps
Line Impedance : 135 Ohms
Transmit Signal Power : 16 dBm +/- 0.5dBm
Operating Range in 2 Wire : 6 Kms. on 0.5mm diameter copper cable @ 2.048Mbps data rate
Operating Range in 4 Wire : 8 Kms. and Above on 0.5mm diameter copper cable @ 2.048Mbps data rate
Operating Mode : 2Wire or 4 Wire selection through DIP switches
Line protection : As per ITU-T K20 and K21
Transmit Level : Upto 16dBm
Connector : RJ 45
Surge Protection : Internal and Optional External Surge Protection
Interface : E1 Interface (4 wire) as per CCITT G.703, G.704 .
Framing : As Per ITU-T G.703 and G.704 Framed and Unframed Operation (Supports PCM31 and PCM30 with the CRC Enable and Disable Operation)
Line Code : HDB3
Speed : 2.048 Mbps (n*64), N=1 to 32)
Impedance : 120 Ohms (Balanced), Optional : 75 Ohms (Unbalanced)
CRC : CRC-4 Generation and Checking
Transmit Clock Mode : Internal clock or G.703 Recovered clock/Recovered from line
Timeslot Selection : Programmable Time slot selection
Connector : RJ45
External ( Recovered from the E1 Interface ) , Internal , Recovered From DSL Lin
Local Loopback, Digital Loopback and Remote Loopback as per the ITU-T V.54 standard.
All loop back tests and BERT should be operated through Front Panel switches.
Built in test 511 pattern generation and checking (BERT) for the DSL Line as well as the PCM E1 Checking.
End to End Diagnostics and Status Monitoring is through the Embedded Operation Channel EOC without Interrupting the Data
Modem Configuration Through Dipswitches.
PWR, MR, COT, DSL LINK, DTR, RTS, PAT, ERR, TST
DUAL MODE AC/DC, 230VAC +/- 10% & –48VDC +/-10%
-5 To 60°C
Upto 95% non condensing
As per ITU K.20/K.21
2 or 4Wire Operation
LED Indications for easy Monitoring.
Supports 230V AC and 48V DC with the Same Socket
Line Impedance : 135 Ohms
Transmit Level : Upto 16dBm
Connector : RJ 45
Interface : E1 Interface (4 wire) as per CCITT G.703, G.704
Data Rates : 2.304 Mbps (n*64 Kbps, n=1 to 36)
Connector : V35 Pin Female Connector